caparol_pim_import/caparol_de/products/image/106350/039091_AkkordVliesG130AA_AkkordVlies_G190AA.png

Capaver AkkordFleece G130/190 AA

White pigmented glass fleece for renovation, made of natural raw materials. Water-activatable (AA), pre-glued on the reverse side. Suitable for bridging shrinkage and drying cracks.

  • LV Texte

    Field of Application

    Capaver glass fleeces provide for highly attractive, high-grade and individual wall surfaces, due to variations in texture, type, colour shade, gloss level and application technique of topcoats.
    In accordance with the expected degree of stress or desired visual appearance, all fabrics may easily be coated with suitable paints and economic renovations are possible, due to individual needs.

    Material Properties

    • Water-activatable glue on the reverse side.
    • Pre-coated in white.
    • Easy to renovate: Recoatable without any pre-treatment.
    • Rot proof, dimensionally stable.
    • Covers small surface cracks (crack bridging).

    Material Base / Vehicle

    Capaver glass fleeces (glass fiber non-wovens) are made of high-quality, purely mineral glass yarns.

    Types that can be delivered

     Type / Product Name Texture Weight per m2 Roll Size
     AkkordVlies G190 AA fine–medium Approx. 210 g 25 x approx. 1 m
     AkkordVlies G130 AA fine

     Approx. 160 g

     50 x approx. 1 m
    Fabric weight with glue.

    Packaging/Package Size

    See table above. Selectable unit: One carton per roll.

    Storage

    Keep Capaver glass fleeces in a dry place.

    Mass per unit area

    Surface weight / See table above (Weight per m2).

    Note

    Capaver glass fleeces are composed of glass fibres (Amer. term: glass fibers) with a diameter > 5 µm, particles of that size cannot enter the respiratory tract. Although the fibres are highly bonded in the fabric, a limited amount of glass particles may be released when cutting the fibres/glass fleeces. This may cause itching of skin to people with a sensitive skin, during application, but will fade away after bonding. Advice: Use P2 dust filter/mask during work. Capaver glass fleeces do not release any glass fibres after being coated.

    Glass fleeces of Aqua Active (AA) type are pre-coated in white and therefore usually require only one finishing coat, when matt/silk-matt paints are applied and white or pastel shades are used. Nevertheless, a previously applied trial coating is advisable.

    Dynamic cracks in the substrate cannot be durably bridged (removed) with Capaver AkkordVlies
    G130/190 AA.

    Suitability according to Technical Information No. 606 Definition of Application Areas

    Interior 1Interior 2Interior 3Exterior 1Exterior 2
    ++
    (–) inapplicable / (○) of limited suitability / (+) suitable

    Substrates

    Interior surfaces: Mineral plasters in mortar groups/classes PI (lime plaster), PII (lime-cement mortars) and PIII (cement mortars), PIV (gypsum mortar and ready-mixed gypsum plasters), gypsum cardboards/pasterboards/drywalls, gypsum wallboards, concrete.

    Surfaces with colour contrast: One previously applied priming coat of Capadecor DecoGrund or Haftgrund.

    Substrate Preparation

    The substrate must always be solid, dry, sound/stable, clean, even and free from all substances that may prevent good adhesion. Follow Technical Information No. 650. In Germany: Follow VOB, part C, DIN 18366, section 3. Lower temperature limit for application and drying: +5 °C (product, substrate and ambient air).

    Method of Application

    For bonding Aqua Active glass fleece no adhesive (glue) has to be roller or spray applied to the substrate! Application is effected in a water bath tray/unit or in a suitable wallpaper pasting machine with conversion kit:

    • In a first step fill the pasting machine with tap (potable) water.
    • Then inlay the roll in conformity with technical manual and reset the counter (if available).
    • After that draw the fabric through the unit in 2/3-1/3 method per length and fold it or directly bond to the wall.
    • The adhesive (glue) is quickly self-activating and has reached the optimum adhesive power after approx. 1 minute.
    • For application on ceilings a longer dwell time of 2 - 3 minutes is advisable.
    • Note: Longer dwell times may lead to a difficult opening of lengths.
    • Wall coverings with a dwell time of >5 minutes must not be bonded.
    • Important: As long as  the adhesive (glue) has no contact to the wall surface, the glue can be (even after drying) repeatedly reactivated with tap water.


    Bedding/Bonding of Glass Fabrics and Fleeces

    • The reverse side of the roll is normally marked and has to be bonded to the wall. To avoid differences of appearance in texture/pattern, always place the fabrics running in one direction and not laterally reversed (upside-down).
    • Capaver glass fleeces like AkkordVlies G130 and 190 should be bonded with butt joints, whereby double seam cut is possible for all glass fleeces.
    • Provide for narrow butt joints, but the forming of bulges must be avoided to achieve a proper visual appearance.
    • Press the bonded fleece lengths void-free with sufficient pressure to the full surface using wallpaper scraper or pressure roller. Fix the edges and cut of the excess length with a wallpaper scraper.
    • Hint: For bonding glass fleeces on vertical external corners, the length must pass around it for minimum 10 cm. For non-vertical corners, the fleece must be cut at the corner.

    Surface Coating System

    Intermediate Coat:
    The intermediate coat forms the basis to achieve a perfect finishing coat. The intermediate coat can only be applied when adhesive (glue) and fleeces are completely dry, and should be tinted to match the finishing coat in shade. Capaver Gewebegrundierung should be used as a filling intermediate coat before applying non-filling (thin film) finishing coats of e.g. latex paints.
    AkkordVlies G 130/190 AA: In most cases an intermediate coat can be omitted for dull(dead)-matt painting in light (pastel) colour shades. This has to be checked by a trial coating.

    Finishing Coats:
    Selection of suitable products for finishing coats is depending on the degree of expected loads and desired gloss level. Coatings must be applied wet-on-wet (also effective for trimming areas).
    See the following table.

    LoadsIntermediate CoatFinishing CoatGloss
    Level
    ProductWork StepsProductWork Steps
    NORMALCapaTrend
    Malerit E.L.F.
    Sylitol Bio-Innenfarbe
    1CapaTrend
    Malerit E.L.F.
    Sylitol Bio-Innenfarbe
    1MATT
    NORMAL–
    MEDIUM
    CapaMaXX 
    MattLatex
    CapaSilan
    NespriSilan
    1CapaMaXX 
    MattLatex
    CapaSilan
    NespriSilan
    1MATT
    Indeko-plus1Indeko-plus1MATT
    MEDIUM–
    HIGH
    Amphibolin
    Latex Samt 10
    1Amphibolin
    Latex Samt 10
    1SM
    SeidenLatex1SeidenLatex1SGL
    Amphibolin1–2 depending on colour shadeMetallocryl Interior2GL
    EffektGrund1–2 depending on colour shadeCapaGold/CapaSilver2SGL
    HIGHPremiumClean1PremiumClean1SM
    Latex Satin 20
    Latex 201 SG
    1Latex Satin 20
    Latex 201 SG
    1SGL
    Latex Gloss 601Latex Gloss 601GL
    EXTREMELY HIGHDisbopox 447
    E.MI
    Wasserepoxid
    1Disbopox 447
    E.MI
    Wasserepoxid
    1SGL

    For more details please consult our corresponding Technical Information of above mentioned products. 

    ProductLoadability
    CapaTrend 
    Malerit E.L.F
    Sylitol Bio-Innenfarbe
    - Wet scrub resistance Class 3 as per DIN EN 13300
    CapaMaXX 
    MattLatex
    CapaSilan
    NespriSilan
    - Wet scrub resistance Class 2 as per DIN EN 13300
    - Resistant to aqueous disinfectants
    Indeko-plus
    Amphibolin
    Latex Samt 10
    SeidenLatex
    Premium Clean
    Latex Satin 20
    Latex 201 SG
    Latex Gloss 60
    Metallocryl Interior
    CapaGold/CapaSilver
    - Wet scrub resistance Class 1 as per DIN EN 13300
    - Resistant to aqueous disinfectants
    Disbopox 447 E.MI Wasserepoxid- Wet scrub resistance Class 1 as per DIN EN 13300
    - Resistant to aqueous disinfectants
    - Highly scratch- and shock-resistant
    - Chemical-resistant
    - Decontaminable as per DIN 25415

    Not tested for resistance to disinfectants.

    Drying/Drying Time

    Allow bonded lengths of glass fleeces to dry thoroughly before any further coating.

    Note

    On principle the marked interior side of a roll has to be bonded to the wall. The outer side of the roll is
    the visible face. To avoid differences of appearance in texture/pattern, always place the fleeces running
    in one direction and not laterally inverted.

    Capaver wall coverings are thoroughly inspected by the manufacturer. In exceptional cases isolated production related weaving faults may occur. These faults are marked at the trimmed edges and correspondingly compensated. They do not entitle to any objection. While cutting the fleeces (lengths), ascertain whether there are no weaving faults. In case of complaint the label with the batch and product numbers must be kept ready. Claims based on material faults cannot be objected after the application of more than 10 lengths.

    German Certificates

    • Flame-retardancy according to German standard DIN 4102, B1
    • Non-combustibility according to German standard DIN 4102, A2
    • Decontaminatibility in combination with Disbopox 447 E.MI Wasserepoxid

     

    Fire behaviour classification associated with Capaver® AkkordVlies G130/190 AA
    CoatingReaction to Fire: Class
    CapaTrendA2
    Malerit E.L.F.A2
    CapaMaXXA2
    MattLatexA2
    Indeko-plusA2
    CapaSilanA2
    Sylitol Bio-InnenfarbeA2
    Latex Samt 10A2
    Latex Satin 20A2
    Latex Gloss 60A2
    Amphibolin E.L.F.A2
    Nespri®SilanB1
    SeidenLatexB1
    SG201B1
    PremiumCleanB1
    Disbopox 447 E.MI WasserepoxidB1

    German test certificates for the corresponding products are available via www.caparol.de

    Disposal

    Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures.
    In Germany: Dispose Capaver glass fabrics and fleeces as construction site waste.

    Technical Assistance

    As it is impossible to list herein the wide variety of substrates and their specific problems, please
    request our technical assistance in case of queries. We will describe appropriate working methods, if a
    substrate not specified above is to be coated.

    Customer Service Centre

    Tel.: +49 06154- 71 7 1710
    Fax: +49 05154- 71 7 1711
    e-mail: kundenservicecenter@caparol.de

    International Distribution: Please see www.caparol.com

    Product recommendation:

    CapaMaXX

    CapaSilan

    Capaver Gewebegrundierung

    Indeko-plus

    Sylitol® Bio-Innenfarbe