Capacryl Spray-TEC Filler

Emulsion based undercoat lacquer (priming varnish) and filler for interior use.
LV Texte

Field of Application

Highly filling undercoat lacquer, suitable for airless spray application on primed surfaces in interiors before applying waterborne enamels, e.g. Capacryl Spray-TEC Satin and Capacryl PU-Satin/PU-Gloss.

Material Properties

  • High filling capacity.
  • Excellent opacity (hiding/covering power).
  • High stability up to 450 µm wet film thickness.
  • Very easy to sand.
  • Efficient application with airless spray process.
  • High degree of whiteness.
  • High dry film thickness.
  • Lead- and chromate-free.

Material Base / Vehicle

Acrylic-polyurethane combination

Packaging/Package Size

5 litres



Gloss Level



Keep in a cool, but frost-free place.


Approx. 1.3 g/cm3

Suitability according to Technical Information No. 606 Definition of Application Areas

Interior 1Interior 2Interior 3Exterior 1Exterior 2
(–) inapplicable / (○) of limited suitability / (+) suitable

Suitable Substrates

Primed wood and derived timber products, primed and dimensionally stable metal surfaces, stable existing coatings, primed with Capacryl Haftprimer (wash primer), in interiors.

Substrate Preparation

Sand and clean the primered surfaces.

Preparation of Material

Stir well before use. Spray preferably undiluted or diluted to a max. of 5 % with tap (potable) water, if necessary.

Method of Application

Advice for Spray Application:

Ø NozzlePressureDilution
Airless0,010-0,014 inch180 - 200 barUndiluted or diluted to a max. of 5 % by volume with tap (potable) water

Advice: Dilution reduces the stability and filling capacity.


Spray preferably undiluted or diluted to a max. of 5 % with tap (potable) water, if necessary.

Layer Thickness

Wet film thickness: Max. 450 µm

Surface Coating System

SubstrateUseSubstrate PreparationPriming CoatIntermediate CoatIntermediate CoatFinishing Coat
Wood, derivative timber productsInteriorSand/cleanCapacryl Holz-IsoGrundCapacryl Spray-TEC FillerIf necessary: Capacryl Spray-TEC Satin or Capacryl PU-Satin/PU-GlossCapacryl Spray-TEC Satin or Capacryl
Iron, steelInteriorDerust/cleanCapalac AllGrund
Zinc, galvanised surfacesInteriorBFS No. 5Capacryl Haftprimer
AluminiumInteriorBFS No. 6Capacryl Haftprimer
Hard/unplasticized PVCInteriorBFS No. 22Capacryl Haftprimer
Sound existing paint coatings1)InteriorSand slightlyCapacryl Haftprimer
1) Prepare and prime damaged spots according to the respective substrate requirements. 
Note: Adhesion must be tested in advance for powder coatings, coil coatings and other critical substrates by trial coating.


Approx. 220 ml/m2 at 200 µm wet film thickness. 
Consumption is a reference value and may vary, depending on the nature of substrates and substrate condition. 
Determine the exact amount of material required by coating a test area on site.

Application Conditions

Lower Temperature Limit for Application and Drying:
Min. +10 °C for product, substrate and ambient air.
Relative humidity must not exceed 70 %.

Drying/Drying Time

At 20 °C and 65 % relative humiditydust dryrecoatable
Drying times1)approx. 60 minutes at 200 µm wet-film thickness2)8 hours

1) Lower temperatures and higher humidity extend the drying time. 
2) Higher wet film thickness extend the drying time.

Tool Cleaning

Immediately after use with water.

Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)

May cause an allergic skin reaction. If medical advice is needed, have product container or label at hand. Keep out of reach of children. Do not get in eyes, on skin, or on clothing. Wear protective gloves/ eye protection. IF ON SKIN: Wash with plenty of soap and water. Contains: 1,2-benzisothiazol-3(2H)-one, 2-methyl-2H-isothiazol-3-one, mixture of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no. 247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1). mixture of: 5-chloro-2-methyl-4-isothiazolin-3-one and 2-methyl-2H-isothiazol-3-one (3:1) < 15 ppm


Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures. 
In Germany: Only completely empty containers should be handed in for recycling. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels. Dispose dried/hardened product residues as construction site/demolition/municipal or domestic waste.

EU limit value for the VOC content

of this product (category A/d): max. 130 g/l (2010). This product contains max. 80 g/l VOC.



Substances of Content - Declaration

Polyacrylic resin, titanium dioxide, silicates, calcium carbonate, aluminum hydroxide, water, glycol ethers, ester alcohol, additives, preservatives.

Customer Service Centre

Tel.: +49 6154 71-71710
Fax: +49 6154 71-71711

International Distribution: Please see