Capadur ClassicLasur

Suitable Substrates

Limited and non-dimensionally stable wooden components. The substrate must be clean, stable and free from separating substances. The exterior wood moisture content must not exceed 12 % on average for hardwoods and 15 % on average for softwoods. The principles of constructive wood protection must be observed. These are a prerequisite for durable wood protection with coating materials.

Substrate Preparation

The wooden surfaces must be cleaned of dust, dirt, resin pockets, grease, oil, etc. before coating. Thoroughly brush off any sanding dust or loose residue from old coats. Silicone residues lead to levelling problems.

New Wooden Parts:
Sand smooth and planed wood surfaces in the direction of the grain and clean thoroughly. Remove escaping wood substances such as resins and resin pockets.
Untreated exterior wood should be coated immediately before it is exposed to the weather (UV radiation, precipitation, wind). Otherwise, reduced paint adhesion caused by the formation of a separating layer is to be expected. The degree of problematic nature of this separating layer cannot be determined with standard building site tests.

Untreated Existing Wood:
Sand greyed, weathered wood surfaces down to the healthy, stable wood and clean thoroughly.

Coated Wood:
Completely remove old coatings that are not stable down to the wood. Sand and clean adhering old coatings and check for compatibility with Capadur ClassicLasur.

Method of Application

Application:

Stir Capadur ClassicLasur before use.
Apply two coats undiluted. For maintenance coats on Capadur ClassicLasur, apply one or two undiluted coats. Only spray in closed systems with extraction equipment.

Surface Coating System

Substrate	Impregnation on wood at risk of blue stain	Priming/Intermediate Coat	Finishing Coat
Limited stable and unstable wood	Capalac Holz-Imprägniergrund	1 - 2 x Capadur ClassicLasur	Capadur ClassicLasur

Consumption

Brush application on smooth wooden surfaces:
Approx. 60 - 80 ml/m² depending on the absorbency of the substrate

Brush application on rough sawn wood surfaces:
Approx. 85-105 ml/m² depending on the absorbency of the substrate.

The consumption values are reference values that may vary depending on the substrate and substrate condition. Exact consumption values can only be determined by prior test coatings.

Application Conditions

• Material, circulating air and substrate temperature: at least 5 °C (favourable range: 10 to 25 °C)
• Relative humidity must not exceed 80 %.

Drying/Drying Time

At 23 °C and 55 % relative humidity:
recoatable after 6-8 h, rainproof after 12 h.

Tool Cleaning

Clean tools after use with synthetic resin thinner or universal thinner.

Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)

May cause an allergic skin reaction. Harmful to aquatic life with long lasting effects. Avoid breathing mist or vapors. Avoid release to the environment. Wear protective gloves. If skin irritation or rash occurs: Get medical advice/ attention. Take off contaminated clothing and wash it before reuse. Dispose of contents/ container to an approved waste disposal plant. Repeated exposure may cause skin dryness or cracking. Contains: Reaction mass of bis(1,2,2,6,6-pentamethyl-4-piperidyl) sebacate and methyl 1,2,2,6,6-pentamethyl-4-piperidyl sebacate, 3-iodo-2-propynyl butylcarbamate, Fatty acids, C18-unsatd., dimers, compds. with coco alkylamines, 4,5-dichloro-2-octyl-2H-isothiazol-3-one, octhilinone (ISO). For commercial/industrial applications.  
Hotline for allergy enquiries: 0800/1895000 (free of charge from the German landline network).

Disposal

Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local, regional, national and international authorities. Must not reach sewage system or environment.

EU limit value for the VOC content

of this product (category A/e): 400 g/l (2010). This product contains max. 350 g/l VOC.

Giscode

BSL20

Substances of Content - Declaration

Alkyd resin, linseed oil, silicates, aliphatics, water, ester, glycol ethers, aromatics, additives.

Further Details

See Material Safety Data Sheet (MSDS).

Technical Assistance

All substrates encountered in practice and their technical processing cannot be dealt with in this publication. If substrates are to be treated that are not listed in this technical information, it is necessary to consult us or our sales representatives. We will provide you with detailed and object-related advice.

Customer Service Centre

Tel.: +49 6154 71-71710
Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de

International Distribution: Please see www.caparol.com