Capalac Rostschutzgrund
Rust inhibitive primer for iron and steel.
Field of Application
Suitable for corrosion inhibiting (anti-rust) priming coats on iron and steel. For exterior and interior use.
Material Properties
- Unleaded and free of chromates.
- High corrosion protection.
- Active rust-inhibiting pigments.
- Excellent adhesion.
- High opacity (hiding/covering power).
- Fast-drying.
- Easy to apply.
Material Base / Vehicle
Alkyd resin, solvent-based.
Packaging/Package Size
750 ml, 2.5 litres,
Colours
Light grey
Gloss Level
Matt (flat)
Storage
Keep in a cool place.
Keep cans/containers tightly closed.
Density
Approx. 1.5 g/cm3
Suitability according to Technical Information No. 606 Definition of Application Areas
| Interior 1 | Interior 2 | Interior 3 | Exterior 1 | Exterior 2 |
| ○ | ○ | ○ | + | + |
| (–) inapplicable / (○) of limited suitability / (+) suitable | ||||
Suitable Substrates
Iron and steel
Substrate Preparation
Derust iron and steel surfaces according to industry standard (metallic bright).
Remove contaminations/soiling, oils, fats/greases and all other materials that may prevent good adhesion.
Method of Application
Capalac Rostschutzgrund can be applied with brush, roller or spraying equipment. Stir well before use. Thin with synthetic resin thinner, if necessary.
Guidelines for Spray Application:
| Ø Nozzle | Pressure | Thinning | Material temperature | |
| High pressure | 1,5 - 1,8 mm | 3–4 bar | max. 10% by volume | - |
| Low pressure | 1,5 - 1,8 mm | 0,2–0,5 bar | max. 10% by volume | - |
| Airless | 0,011–0,013 inch | 180–230 bar | – (delivered viscosity) | 35°C |
Surface Coating System
| Substrate | Use | SubstratePreparation | Priming Coat | Intermediate Coat | Finishing Coat |
| Iron and steel | interior | derusting/degreasing | 1–2x Capalac Rostschutzgrund✱ | if required Capalac Weiß- or Buntlacke or Vorlack | Capalac Weiß- or Buntlacke / white or pigmented Capalac enamels (coloured paints) |
| exterior | derusting/degreasing | 2x Capalac Rostschutzgrund | Capalac Weiß- or Buntlacke or Vorlack |
| ✱ Apply one or two coats of Capalac Rostschutzgrund, depending on the loads/conditions. |
Consumption
| Consumption Rate ml/m2 | Brush Application | Roller Application | Spraying | ||
| High Pressure | Airless | Low Pressure | |||
| vertically | 90–100 | 80–100 | 130 | 140 | 130 |
Application Conditions
Lower Temperature Limit for Application and Drying:
+5 °C for product, substrate and ambient air. Relative humidity must not exceed 80 %.
Drying/Drying Time
| Drying Times at 20 °C, 65 % relative humidity | dust-dry | touch-dry | recoatable (by brush) | recoatable (spraying) |
| after hours | 2–3 | 4–5 | 12 | 6–8 |
Lower temperatures, higher humidity and thick film application extend the drying time.
Tool Cleaning
Immediately after use with solvent naphta/white spirit or suitable synthetic resin thinner.
Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)
Flammable liquid and vapor. May cause drowsiness or dizziness. Harmful to aquatic life with long lasting effects. If medical advice is needed, have product container or label at hand. Keep out of reach of children. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish. Store locked up.Repeated exposure may cause skin dryness or cracking. Contains: Naphtha (petroleum), hydrotreated heavy; Low boiling point ydrogen treated naphtha. Warning! Hazardous respirable droplets may be formed when sprayed. Do not breathe spray or mist. Contains neodecanoic acid, cobalt salt. May produce an allergic reaction.Disposal
Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures. In Germany: Only completely emptied clean cans/containers should be given for recycling. Deliver packaging with residues of liquid material to a collecting/collection point for old enamels.
EU limit value for the VOC content
of this product (category A/i): max. 500 g/l (2010). This product contains max. 500 g/l VOC.
Unthinned product (delivered viscosity): max. 370 g/l VOC.
Product Code Paints and Enamels
M-GP02
Further Details
See Material Safety Data Sheet (MSDS).
Customer Service Centre
Tel.: +49 6154 71-71710Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de
International Distribution: Please see www.caparol.com
