Field of ApplicationWhite enamel/top-coat lacquer for high-quality coatings on wood, metals and unplasticized (rigid) PVC, exteriors and interiors. Do not use on heating systems.
Due to a typical odour of alkyd resin varnishes (alkyd enamels), it is advisable to use Capacryl PU-Gloss for coatings on large, seamless interior surfaces instead.
- Non-aromatic solvent
- High degree of whiteness
- High resistance to yellowing
- Brilliant gloss
- Elegant and easy application
- High stability (low sagging)
- High covering power on edges
- Excellent opacity (hiding/covering power)
- High impact strength and shock resistance
- Long open time
- Resistant to common household cleaning agents (detergents) and short-term resistance against weak acids and alkalis
- High weather resistance and lightfastness
- Superior flow
Material Base / VehiclePolyurethane alkyd resin, solvent-based, free of aromatic hydrocarbons.
750 ml, 2,5 litres
White (Weiß), Off-White (Altweiß)
Note: A material typical yellowing effect may occur on the surface of white/off-white and light-coloured alkyd enamels (caused by low UV radiation, heat or chemical influences due to e.g. ammonia vapour from detergents, adhesives, paint or sealing compounds). This yellowing is no product defect and cannot be objected.
Colour Resistance according to BFS Data Sheet No. 26:
Binder: Class B
Pigmentation: Group 1
Keep in a cool place, in tightly closed cans/containers.
DensityApprox. 1.2 g/cm³
Suitability according to Technical Information No. 606 Definition of Application Areas
|Interior 1||Interior 2||Interior 3||Exterior 1||Exterior 2|
|(–) inapplicable / (○) of limited suitability / (+) suitable|
Suitable SubstratesPrimed and pre-coated wood, iron, steel, zinc/galvanised substrates, aluminium (must not be anodised), and unplasticized/rigid PVC. The substrate must be clean, sound/stable, dry, and free from all substances that may prevent good adhesion.
Substrate PreparationRoughen/sand the primed surface and clean thoroughly.
Method of ApplicationThe product is ready-to-use and can be applied by enamel brush or roller.
Guidelines for Spray Application:
|Ø Nozzle||Pressure||Thinning/Dilution||Material Temperature|
|Aircoat-TempSpray||0,009 - 0,013 inch||150 bar||delivered viscosity||35 °C|
Surface Coating System
|Substrate||Use||Substrate Preparation||Impregnation||Priming Coat||Intermediate Coat||Finishing Coat|
|Wood & derivatives||interior||roughening (sanding)||–||Capalac Vorlack||–||Capalac SuperWeiß|
|Dimensionally stable wood components||exterior||BFS No. 18||Capalac Holz-Imprägnier-Grund||Capalac Vorlack||Capalac SuperWeiß|
|Iron, steel||interior||derusting/degreasing||–||Capalac Allgrund or Rostschutzgrund||–|
|exterior||derusting/degreasing||–||2 x Capalac Allgrund |
or 2 x Rostschutzgrund
|Zinc||interior||BFS No. 5||–||Capalac AllGrund||–|
|exterior||BFS No. 5||–||Disbon 481 EP-Uniprimer or 2 x Capalac AllGrund||Capalac SuperWeiß|
|Aluminium||interior||BFS No. 6||–||Capalac AllGrund||–|
|exterior||BFS No. 6||–||Capalac AllGrund||Capalac SuperWeiß|
|Rigid PVC||interior/exterior||BFS No. 22||–||Capalac AllGrund||–|
Stable existing coats of paint
slightly sanding/alkali treatment
Prepare and prime defects according to substrate requirements
Advice: Adhesion must previously be tested for powder coatings, coil coatings and other critical/problematic substrates by a trial coating.
Consumption ml/m2 per Coat
|Brush Application||Roller Application||Aircoat|
|80 - 100||70 - 90||120|
Determine the exact amount of material required by coating a test area on site.
Application ConditionsLower Temperature Limit for Application and Drying:
+5 °C for product, substrate and ambient air.
Relative humidity must not exceed 80 %.
At 20 °C and 65 % relative humidity
|dust dry||touch dry||recoatable (brush)||recoatable (spray)|
|after hours||3||5||8||8 - 16|
Lower temperatures, higher humidity and higher quantities of applied material extend the drying time.
Tool CleaningImmediately after use with white spirit.
Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)Flammable liquid and vapour. Harmful to aquatic life with long lasting effects. If medical advice is needed, have product container or label at hand. Keep out of reach of children. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. Avoid release to the environment. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. Repeated exposure may cause skin dryness or cracking. Contains bis(1,2,2,6,6-pentamethyl-4-piperidyl) sebacate, methyl 1,2,2,6,6-pentamethyl-4-piperidyl sebacate. May produce an allergic reaction. Use P2 dust filter for grinding. Do not breathe spray dust. Use A2/P2 combination filter for paint spraying.
DisposalMaterials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures.
In Germany: Only completely empty containers should be handed in for recycling. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels. Dispose dried/hardened product residues as construction site/demolition/municipal or domestic waste.
EU limit value for the VOC contentof this product (category A/d): max. 300 g/l (2010). This product contains max. 300 g/l VOC.
Product Code Paints and EnamelsM-LL01 (Germany)
Substances of Content - DeclarationAlkyd resin, titanium dioxide, aliphatic hydrocarbons, driers, anti-skinning agent, additives.
Further DetailsSee Material Safety Data Sheet (MSDS).
Product name: Capalac SuperWeiß
Customer Service CentreTel.: +49 6154 71-71710
Fax: +49 6154 71-71711
International Distribution: Please see www.caparol.com