Field of Application
Ready-to-use mortar for the embedding of reinforcing fabric to create the reinforcement layer on thermal insulating boards made of mineral wool like
- Capatect MW-Fassadendämmplatten type "zg"
- Capatect LS-Fassadendämmplatte VB 101
within the system Capatect ETICS Carbon Extra
- Reaction to fire: A2-s1,d0 (non-combustible) as per DIN EN 13501-1
- Easy to apply
- Low material consumption
- Excellent adhesion
- Highly shock-proof and non-cracking
- Impact resistance up to 20 Joule (1 layer system)
- Impact resistance up to 60 Joule (2 layers system)
Packaging/Package Size20 kg bucket
StorageCool, dry and frost-free and protected against direct sunlight.
Densityapprox. 1.3 g/cm³
Diffusion-equivalent air layer thickness sdH2O< 0.5 m as per DIN EN ISO 7783, class V2 as per DIN EN 15824
Fire behaviourA2-s1, d0 as per DIN EN 13501-1
Vehicle / Binding agentSilicate-organo-hybride emulsion
Water permeability (w-value)≤ 0.1 kg/(m2·h0,5) as per DIN EN 1062-3,
class W3 as per DIN EN 15824
Data stated above are average values, which may slightly vary from batch to batch (supply) due to the use of natural raw materials.
Not suitable with mineral top coatings (e.g. finishing render or reinforcement mortar).
Suitable SubstratesAll substrates must be load-bearing, dry, flat (DIN 18202 or 18203), clean and free of adhesion-reducing residues.
Preparation of Material
Capatect OrCa-Spachtel is ready to use and should only be stirred up shortly before use. The consistency may be adjusted by adding a small quantity of tap water.
Method of Application
Diagonal reinforcement: Before the application of the reinforcement over the entire area, diagonal reinforcement elements or fabric strips must be embedded diagonally in the corner area of building openings.
Reinforcement layer: To ensure an uniform, even surface, double-layer processing is recommended: Apply the first layer of Capatect OrCa-Spachtel (approx. 1 - 2 mm layer thickness) to stabilize the insulation board surface.
After curing of this layer apply the same reinforcement mortar onto the thermal insulating boards in the width of a reinforcing fabric sheet. Press reinforcing fabric Capatect OrCa-Gewebe 653 very thoroughly into the freshly applied, still wet reinforcement layer with an overlap of approx. 10 cm. Than apply a subsequent layer of reinforcement mortar (wet-on-wet), to guarantee the complete embedding of fabrics. The fabric should be embedded in the upper third of the reinforcement layer. Provide for a total reinforcement layer thickness of approx. 4-5 mm.
Approx. 1.3 kg/m2 per mm of layer thickness. Discrepancies should be considered due to site and application conditions.
Application ConditionsProcessing temperature: + 8 °C to approx. + 30 °C for material, substrate, water and ambient air during application and curing. Do not apply in direct sunlight, during strong wind, fog, high relative humidity, and imminent rain or frost.
Drying/Drying TimeAt 20 °C and 65% RH the reinforcement layer is surface-dry after 24 hours and thoroughly dry and ready for stress after 2 to 3 days. Depending on atmospheric conditions (at the earliest after 2 to 3 days) the reinforcement layer can be coated with Capatect ThermoSan-Fassadenputz NQG.
Please Note (Status as at Date of Publication)
Keep out of reach of children. Ensure good ventilation during use and drying. Do not eat, drink or smoke while using the product. In case of contact with eyes or skin, immediately and thoroughly rinse with water. Do not allow product to enter drains, waterways or soil. Contains a mixture of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1), 2-hydroxypropylneododecanoate, 2-methyl-2H-isothiazol-3-one. Can cause allergic reactions.
In Germany: Advice for allergy sufferers with isothiazolinone allergy via hotline 0800/1895000 (free of charge from German landline).
Further details: see Material Safety Data Sheet
DisposalMaterials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures. Only completely emptied containers should be given for recycling. In Germany: Dispose containers with residues of liquid material as remnants of water-based paints and dried material as hardened paints waste or via domestic waste.
EU limit value for the VOC contentas per EC Directive 2004/42: < 1%; < 10 g/l
Product Code Paints and EnamelsM-DF02 (outdated)
Further DetailsAssessments and approvals: ETA-09/0368
Customer Service CentreTel.: +49 6154 71-71710
Fax: +49 6154 71-71711
International Distribution: Please see www.caparol.com