caparol_pim_import/caparol_de/products/image/114505/041545_Histolith_Weissgrund_12_5_Liter.png

Histolith Weißgrund

Silicate based, adhesion promoting priming coat for Histolith® interior paints.
LV Texte

Field of Application

White pigmented priming coat, to be used before applying Histolith® interior paints in order to promote adhesion and to level/homogenize the substrate absorbency.

Material Properties

  • High adhesion to the substrate.
  • Homogenizes the surface absorbency.
  • Good opacity (hiding/covering power).
  • Highly water vapour permeable, sd-value = 0.03 m
  • Solvent-free.

Material Base / Vehicle

Potassium silicate (water glass), acrylic resin, mineral pigments and fillers.

Packaging/Package Size

5 litres, 12.5 litres

Colours

White. The primer can be tinted with Histolith Volltonfarben SI (colourants) or is deliverable ready-tinted ex factory. Tintable via the ColorExpress tinting & mixing machine system.

Storage

Keep in a cool, but frost-free place.

Density

Approx. 1.7 g/cm³

Suitability according to Technical Information No. 606 Definition of Application Areas

Interior 1Interior 2Interior 3Exterior 1Exterior 2
+
(–) inapplicable / (○) of limited suitability / (+) suitable

Suitable Substrates

The substrates must be sound/stable, dry, clean, and free from all substances that may prevent good adhesion. In Germany: Follow VOB, Part C, DIN 18 363, section 3.

Substrate Preparation

New Renders/Plasters in Mortar Groups/Classes PIc (Hydraulic Lime Plaster),
PII (Lime-Cement Mortars) and PIII (Cement Mortars):
Allow to set for 2 to 4 weeks. Remove sintered skin with Histolith® Fluat.

Uncoated Existing Renders/Plasters in Mortar Groups/Classes PIc, PII, PIII
and Coats of Mineral Paint:

Carefully clean the surface. Remove all coats/layers of low adherence. Apply one priming coat of Histolith® Silikat-Fixativ, thinned in ratio of 2:1 to 1:1 with tap water, to strengthen slightly sanding render/plaster surfaces.

Sound/Stable Existing Coats of Matt (Flat) Emulsion Paint: Carefully clean the surface.Gypsum Renders/Plasters in Mortar Group/Class PIV:
Strengthen soft gypsum plasters with Histolith® Spezialgrundierung (special primer).
Sand gypsum plasters with sintered skin, then remove sanding dust and apply one priming coat of
Histolith® Spezialgrundierung.

Gypsum Plasterboards (Sandwich-Type Plaster Boards):
Sand down filling burrs. Strengthen soft filled gypsum patches with Histolith® Spezialgrundierung.
For boards with water-soluble, discolouring content that leaves marks, apply one priming coat of
Caparol Aqua-Sperrgrund. In Germany: Follow BFS Data Sheet No. 12.

Gypsum Wallboards: Coat without pre-treatment.

Concrete: Remove any existing parting agent residues.

Brickwork / Brick Masonry:
Carefully clean the surface. Repair defective mortar joints. Apply one priming coat of Caparol Aqua-Sperrgrund for bricks with water-soluble, discolouring content that leaves marks.

Existing Coats of Glue-Bound Distemper:
Wash off (remove) thoroughly. Prime with Histolith® Spezialgrundierung (special primer).

Glass Fabric Wall Coverings: Coat without pre-treatment.

Mildewed Surfaces:
Wash off the fungal (fungi/mildew/mould) attack. Apply Histolith® Algenentferner (algae remover) on
the fully dry surface, then allow to dry again. Prior consultation with our technical assistance is needed
to achieve the correct surface coating system.

Method of Application

Histolith® Weißgrund can be applied by paint brush, roller or airless spraying equipment.

Surface Coating System

Application: Undiluted or thinned to a max. of 3 % with tap (potable) water.

Consumption

Approx. 150 - 200 ml/m2 on an even substrate. On rough-textured surfaces correspondingly more.
The exact consumption is best established by a trial coating (test area) on site.

Application Conditions

Lower Temperature Limit for Application and Drying:
+8 °C for product, substrate and ambient air.

Drying/Drying Time

At +20 °C and 65 % relative humidity surface-dry after 4 - 6 hours and recoatable after 12 hours.
Lower temperatures and higher humidity extend the drying time.

Tool Cleaning

Clean tools/equipment immediately after use with water.

Please Note (Status as at Date of Publication)

Keep out of reach of children. Avoid release to the environment. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. IF ON SKIN: Wash with plenty of soap and water. Further information: See Material Safety Data Sheet (MSDS).

Disposal

Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures.
In Germany: Only completely emptied containers must be given for recycling. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels. Dispose dried/hardened product residues as construction site/demolition/municipal or domestic waste.

EU limit value for the VOC content

of this product (category A/a): 30 g/l (2010). This product contains < 1 g/l VOC.

Product Code Paints and Enamels

M-GP01

Technical Assistance

As it is impossible to list herein the wide variety of substrates and their specific problems, please request our technical assistance in case of queries. We will describe appropriate working methods, if a substrate not specified above is to be coated.

Customer Service Centre

Tel.: +49 06154- 71 7 1710
Fax: +49 05154- 71 7 1008
e-mail: kundenservicecenter@caparol.de

International Distribution: Please see www.caparol.com