Wet scrub resistance Class 2.
Corresponds to "scrub resistant" as per
German standard DIN 53778.

  • LV Texte

    Field of Application

    For high-quality, scrub resistant and texture-retaining interior coatings providing a dull matt surface appearance. The product is applicable in sensitive working and living areas, due to the solvent-free formula. Suitable for renovation and coating of woodchip/ingrain, relief or embossed wallpapers and Capaver glass fabric wall coverings.

    Material Properties

    • Emission-minimised, solvent-free, unplasticized.
    • Free of fogging-active substances.
    • Water-dilutable, ecologically compatible, low odour.
    • Diffusion-capable.
    • sd-value < 0.1 m.
    • High opacity (hiding/covering power), in most cases one coat is sufficient.

    Material Base / Vehicle

    Synthetic latex according to German standard DIN 55 945.

    Packaging/Package Size

    • Standard Product: 12.5 litres.  Airfix: 25 litres hobbock
    • Off-White: 15 litres.  Airfix: 25 litres hobbock
    • Light/Bright White: 12.5 litres.  Airfix: 25 litres hobbock
    • ColorExpress: 12.5 litres


    White, Off-White (approx. RAL 9010) and Light/Bright White (approx. RAL 9016).

    MattLatex can be tinted with CaparolColor or AmphiColor® (AVA) colourants. If more than one bucket is manually tinted, all product must be thoroughly mixed before use in order to avoid colour differences. Quantities of 100 litres or more in individual colours may be ordered ready-tinted ex factory.

    MattLatex is tintable to all current colour collections via the ColorExpress tinting & mixing machine system in light colour shades to luminosity/lightness index (LI) approx. 70. Check tinted paint before applying to avoid colour differences. Always use tinted product of same batch, when applying on seamless surfaces.
    Brilliant, intensive colours may have a lower opacity. It is therefore advisable to apply a first coat in a similar hiding pastel tint, based on white. Possibly a second finishing coat may be necessary.

    Gloss Level

    Dull matt (Dead-matt according to DIN EN 13 300)


    Keep in a cool, but frost-free place.

    Technical Data

    Technical Data according to DIN EN 13 300:
    Tinting may cause variations.

    Wet abrasion

    Wet scrub resistance Class 2

    Contrast ratio

    Opacity (hiding/covering power) Class 1, with a spreading rate of 8 m2/l or 125 ml/m2

    Maximum particle (grit) size

    Fine (< 100 µm)


    Approx. 1.5 g/cm3

    Suitability according to Technical Information No. 606 Definition of Application Areas

    Interior 1Interior 2Interior 3Exterior 1Exterior 2
    (–) inapplicable / (○) of limited suitability / (+) suitable

    Suitable Substrates

    The substrate must be sound/stable, dry, clean, and free from all substances that may prevent good adhesion. In Germany: Follow VOB, part C, DIN 18363, section 3.

    Substrate Preparation

    Plasters in Mortar Groups/Classes PII (Lime-Cement Mortars) and PIII (Cement Mortars) / Minimum Compressive Strength according to DIN EN 998-1: 2 N/mm2:
    Solid plasters with normal absorbency require no preparatory treatment. Prime highly porous, sanding or absorbent plasters with OptiGrund or CapaSol.

    Gypsum and Ready-Mixed Gypsum Plasters in Mortar Group PIV / Minimum Compressive Strength according to DIN EN 13279: 2 N/mm2:
    Apply one priming coat of Haftgrund. Sintered plaster surfaces: Sand/grind off sintered skin, remove all abrasive dust and prime with Tiefgrund TB.

    Gypsum Building Boards / Wallboards:
    Prime absorbent boards with OptiGrund or Tiefgrund TB. Prime highly compact, smooth boards with Haftgrund to enhance adhesion. 

    Gypsum Plasterboards (Sandwich-Type Plaster Boards / Drywalls): 
    Sand/grind off all filler (mortar) burrs. Prime and strengthen soft gypsum areas (repairs) with
    Tiefgrund TB. Prime with Haftgrund, OptiGrund or CapaSol.
    Boards containing water-soluble, discolouring substances that leave marks must be primed with Caparol AquaSperrgrund. In Germany: Follow BFS Data Sheet No. 12.

    Remove all residues of separating agent (formwork oil residues) and chalking or sanding materials.

    Autoclaved Aerated Concrete (AAC) / Cellular Concrete:
    Prime with a 1 : 3 mixture of Capaplex and tap (potable) water.

    Facing Brickwork and Fair-Faced Calcium Silicate (Sand-Lime) Brick Masonry:
    No preliminary treatment required.

    Sound/Stable Existing Coatings:
    Matt, slightly absorbent coatings may be coated without any pre-treatment. Roughen/sand glossy surfaces and enamel coatings. Prime with Haftgrund.

    Unstable Existing Coatings:
    Remove unstable coatings of enamel and dispersion/emulsion/latex paint or synthetic (organic) plaster. Prime slightly absorbent, smooth surfaces with Haftgrund. Prime highly porous, sanding or absorbent substrates with OptiGrund or CapaSol. Remove unstable mineral paint coatings by mechanical means and remove dust. Prime with Tiefgrund TB.

    Coats of Glue-Bound Distemper (Limewater Colour/Paint):
    Wash off the existing distemper very thoroughly, allow to dry and prime with Tiefgrund TB.

    Unpainted Woodchip/Ingrain, Relief or Embossed Wallpapers made of Paper:
    Coat without any preliminary treatment.

    Non-Adherent Wallpapers:
    Remove completely and wash off all residues of wallpaper paste/glue and waste paper. Allow to dry and prime with Tiefgrund TB.

    Mildewed/Mouldy Surfaces:
    Remove fungal (fungi/mildew/mould) attack by wet cleaning, then use Capatox or FungiGrund and allow to dry well. Prime according to the type and condition of the substrate. Apply a finishing coat of Indeko-W, Malerit-W or Fungitex-W on strongly infested surfaces, in compliance with current legal/local/official regulations (follow e.g. Ordinance on Biological Agents and Ordinance on Hazardous Substances).

    Surfaces Stained by Nicotine, Water, Soot or Fat/Grease:
    Remove nicotine, soot or fat/grease stains by washing with tap water adding a fat-dissolving household detergent, then allow the substrate to dry well. Clean dried-up water spots by dry brushing-off. Apply an insulating coat of Caparol AquaSperrgrund. Apply one finishing coat of Aqua-inn Nº1 on highly soiled surfaces.

    Wood and Derived Timber Products:
    Coat with waterborne, ecologically compatible Capacryl acrylic enamels or Capacryl PU enamels.

    Small Defects:
    After having completed the necessary preparations, repair small defects with Caparol-Akkordspachtel in accordance with our application instructions, and if necessary, prime subsequently.

    Method of Application

    Applicable with paint brush, paint roller or airless spray equipment.

    Airless Application:
    Spray angle: 50°
    Nozzle size: 0.019" - 0.021"
    Spray gun pressure: 150 - 180 bar
    Stir well and sieve the material before airless application.

    Surface Coating System

    One even, liberally applied coat of MattLatex, diluted to a max. of 5 % with tap (potable) water. Surfaces with colour contrast: One previously applied first coat of MattLatex, diluted to a max. of 10 % with tap water.
    On surfaces with detrimental/critical lighting conditions and a higher absorbency:
    One previously applied coat of TopGrund EG can optimise the open time of following coatings and also minimises the risk of visible lapping and roller marks on the surface.


    Approx. 125 ml/m2 per coat on smooth substrates. On roughly textured surfaces correspondingly more. Determine the exact amount of material required by coating a test area on site.

    Application Conditions

    Lower Temperature Limit for Application and Drying:
    +5 °C for product, substrate and ambient air.

    Drying/Drying Time

    At +20 °C and 65 % relative humidity surface-dry and recoatable after 4 - 6 hours. Completely dry and ready for stress after approx. 3 days. Lower temperatures and higher relative humidity extend the drying time.


    To avoid lapping, the product should be applied wet-on-wet and without interruption. 
    Due to the use of Tiefgrund TB in interiors, a typical solvent odour is released, hence proper ventilation must be provided during application and drying. Use non-aromatic, low-odour AmphiSilan-Putzfestiger in sensitive areas.
    Touching up surfaces is depending on many parameters and may be visible after drying.
    (In Germany: See BFS Data Sheet No. 25)

    German Certificates

    The Fraunhofer Wilhelm-Klauditz-Institute (WKI) has audited the inoffensive application for interior use.
    The material is certified with German TÜV (Technical Supervisory Association) quality mark "pollutant tested / supervised manufacturing process". German certificate is available on request.

    Please Note (Status as at Date of Publication)

    Keep out of reach from children. Ensure good ventilation during use and drying. Do not eat, drink or smoke while using the product. In case of contact with eyes or skin, immediately and thoroughly rinse with water. Do not allow product to enter drains, waterways or soil. Clean utensils immediately after use with soap and water. Do not breathe spray dust.
    Further information: See Material Safety Data Sheet (MSDS).

    Contains 1,2-benzisothiazol-3(2H)-one, 2-methyl-2H-isothiazol-3-one. May produce an allergic reaction.
    In Germany: Advice for allergy sufferers with isothiazolinone allergy: Hotline 0180/5308928
    (0.14 €/minute from German landline, MTS max. 0.42 €/minute).


    Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures. 
    In Germany: Only completely empty containers should be handed in for recycling. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels. Dispose dried/hardened product residues as construction site/demolition/municipal or domestic waste.

    EU limit value for the VOC content

    of this product (category A/a): max. 30 g/l (2010). This product contains < 1 g/l VOC.

    Product Code Paints and Enamels

    M-DF01 (Germany)

    Substances of Content - Declaration

    Polyacrylic resin dispersion/emulsion, titanium dioxide, calcium carbonate, silicates, water, additives, preservative (Methylisothiazolinone, Benzisothiazolinone).

    Technical Assistance

    As it is impossible to list herein the wide variety of substrates and their specific problems, please request our technical assistance in case of queries. We will describe appropriate working methods, if a substrate not specified above is to be coated.

    Customer Service Centre

    Tel.: (+49) 0 61 54 / 71 17 10
    Fax: (+49) 0 61 54 / 71 17 11

    International Distribution: Please see

    Product recommendation:

    Akkordspachtel SXL