CapaDIN
Approved quality Matt interior paint
Field of Application
Multi-purpose paint for coatings on interior walls and ceilings.Due to its easy application, CapaDIN is particularly suitable for large-area projects, where a high ground coverage is required.Material Properties
- Emission-minimised, solvent-free, low odour.
- Free of fogging-active substances.
- Water-dilutable, ecologically compatible.
- Diffusion-capable.
- sd-value < 0.1 m
- Easy to apply.
Material Base / Vehicle
Synthetic resin dispersion/emulsion according to German standard DIN 55945.Packaging/Package Size
- Standard Product: 5 l, 10 l, 12.5 l and 15 l Airfix: 15 l plastic bucket, 25 l hobbock, 120 l paint barrel, 750 l recycling container
- Antikweiß (Off-White): 12.5 l. Airfix: 25 l hobbock
Colours
- White
- Antikweiß (Off-white / approx. RAL 9010).
Tintable with AmphiColor® Vollton- und Abtönfarben or with CaparolColor Vollton- und Abtönfarben. In case of self-tinting, mix the required total quantity to avoid differences in colour shade.
For orders of 100 litres and more in one colour shade and application, also available factory-tinted on request. In order to recognise possible tinting errors, please check for colour shade exactness before application. Only use colour shades of one production (batch) on continuous surfaces.
Gloss Level
Dull matt (Dead-matt according to DIN EN 13 300)
Storage
Keep in a cool, but frost-free place.
Technical Data
Characteristics according to DIN EN 13 300:Tinting may cause variations.
Wet abrasion
Wet scrub resistance Class 3, corresponds to "wash resistant" as per German standard DIN 53778Contrast ratio
Opacity (hiding/covering power) Class 2, with a spreading rate of
6 m2/l or 160 ml/m2
Maximum particle (grit) size
Fine (< 100 µm)Density
Approx. 1.6 g/cm3
Suitability according to Technical Information No. 606 Definition of Application Areas
| Interior 1 | Interior 2 | Interior 3 | Exterior 1 | Exterior 2 |
| + | + | – | – | – |
| (–) inapplicable / (○) of limited suitability / (+) suitable | ||||
Suitable Substrates
The substrate must be sound/stable, dry, clean, and free from all substances that may prevent good adhesion. In Germany: Follow VOB, part C, DIN 18363, section 3.Substrate Preparation
Plasters of mortar group PII and PIII/compressive strength according to DIN EN 998-1 with min.
1.5 N/mm2: Coat solid, normally absorbent renders without pre-treatment. Prime coarsely porous and absorbentrenders with CapaSol RapidGrund or CapaSol Konzentrat.
Gypsum plasters of mortar group PIV/compressive strength according to DIN EN 13279 with
min. 2 N/mm2: One priming coat of HaftGrund EG. Gypsum plasters with sintered skin: Sand, remove dust, prime with Dupa-Putzfestiger.
Gypsum boards: Apply one priming coat of CapaSol RapidGrund or CapaSol Konzentrat on
absorbent boards. Apply one priming coat of HaftGrund EG to highly compacted, smooth boards.
Gypsum boards (plasterboards): Sand off filler burrs. Strengthen soft gypsum filler areas with Dupa-
Putzfestiger. Prime with HaftGrund EG, CapaSol RapidGrund or CapaSol Konzentrat. For boards with
water-soluble, discolouring ingredients, apply one priming coat of Caparol AquaSperrgrund. Observe
BFS Data Sheet No. 12.
Concrete: Remove any release agent residues and chalking, sanding substances.
Aerated concrete: Apply one priming coat of Capaplex, diluted 1 : 3 with water.
Sand-lime brick and exposed brickwork: Coat without pre-treatment.
Load-bearing coatings: Recoat matt, slightly absorbent coatings directly. Roughen glossy surfaces
and lacquer coatings. Apply one priming coat of HaftGrund EG.
Non-stable coatings: Remove non-stable coatings of lacquer, emulsion paint or synthetic resin
plaster. Prime slightly absorbent, smooth surfaces with Haftgrund EG. Prime highly porous, sanding or
absorbent surfaces with CapaSol RapidGrund. Remove non-bearing mineral paint coatings
mechanically and remove dust from the surfaces. Apply one priming coat of Dupa-Putzfestiger.
Distemper coatings: Wash off the primer. Apply one priming coat of Dupa-Putzfestiger.
Unpainted woodchip, relief or embossed paper wallpapers: Coat without pre-treatment.
Non-sticking wallpapers: Remove completely. Wash off paste and waste paper residues. Prime with
Dupa-Putzfestiger.
Mould-infested surfaces: Remove mould or fungal infestation by wet cleaning. Wash surfaces with
Capatox or FungiGrund and allow to dry thoroughly. Apply a priming coat depending on the type and
condition of the substrate. Apply a top coat of Indeko-W, Malerit-W or Fungitex-W to heavily infested
surfaces. Observe the legal and official regulations (e.g. the Biological Substances Ordinance and the
Ordinance on Hazardous Substances).
Surfaces with nicotine, water, soot or grease stains: Wash off nicotine stains as well as soot or
grease stains with water using a grease-dissolving household cleaning agent and allow to dry
thoroughly. Clean dried water stains by brushing dry. Apply a barrier primer coat of AquaSperrgrund.
Apply the final coat of Aqua-inn Nº1 to heavily soiled surfaces.
Wood and wood-based materials: Coat with water-thinnable, environmentally friendly Capacryl
Acryl-Lacken or Capacryl PU-Lacken.
Small defects: After appropriate preparatory work, repair with Caparol-Akkordspachtel according to
processing instructions and, if necessary, re-prim.
Note Q2/Q3 Filling / thin gypsum layers < 0.5mm: When using gypsum-containing, hydraulically
setting levelling compounds in quality level Q2/Q3, a transparent, water-based primer is
recommended. For this, we refer to the Maler&Lackierer leaflet No. 2 -9/2020 "Adhesion problems of
coatings on filled gypsum (cardboard) boards" of the Bundesverband Farbe, Gestaltung, Bautenschutz
and Federal Committee for Paint and Property Protection. As an alternative to gypsum-based Q3
filling, filling with pasty filling compounds has proven successful.
Method of Application
Apply with paint brush, roller or airless equipment.Airless Application:
| Dilution | max. 5% with water |
| Airless equipment | |
| Spray pressure | 150 - 180 bar |
| SSpray angle | 50° |
| Nozzle size | 0,021" - 0,025" |
| Pistol filter in MW | ca. 0,31mm |
| IInternally fed roller systems | |
| Spray pressure | 80 - 120 bar |
| Pistol filter in MW | ca. 0,31mm |
Clean tools/working equipment immediately after use with water.
Surface Coating System
A rich, even coat of CapaDin undiluted or diluted with a maximum of 5 % water. On surfaces withhigh contrast or streaky light, apply one priming coat beforehand, diluted with max. 10 % water. Applyone priming coat of HaftGrund EG on substrates with different degrees of absorbency.Consumption
Approx. 150 ml/m2 per coat on smooth substrates. On roughly textured surfaces correspondingly more. Determine the exact amount of material required by coating a test area on site.Application Conditions
Lower Temperature Limit for Application and Drying:+5 °C for product, substrate and ambient air.
Drying/Drying Time
At +20 °C and 65 % relative humiditysurface-dry and recoatable after 4 - 6 hours. Completely dry and ready for stress after approx. 3 days. Lower temperatures and higher humidity extend the drying time.Note
To avoid build-up, coat wet-on-wet in one go. To ensure an even surface gloss on smooth and/orstreaky surfaces, a second coat may be necessary. For airless spray application, stir the paint well andsieve. Markings of touch-ups in the surface depend on many factors and are therefore unavoidable(BFS Leaflet 25). Use of phenol-based surface disinfectants may lead to yellowing of the surface.Please Note (Status as at Date of Publication)
Keep out of reach from children. Ensure good ventilation during use and drying. Do not eat, drink or smoke while using the product. In case of contact with eyes or skin, immediately and thoroughly rinse with water. Do not allow product to enter drains, waterways or soil. Clean utensils immediately after use with soap and water. Do not breathe spray dust.Contains: 1,2-benzisothiazol-3(2H)-one, 2-methyl-2H-isothiazol-3-one. May produce an allergic reaction.
In Germany: Advice for allergy sufferers with isothiazolinone allergy: Hotline 0180/5308928
(0.14 €/minute from German landline, MTS max. 0.42 €/minute).
Further information: See Material Safety Data Sheet (MSDS).
Disposal
Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures.In Germany: Only completely empty containers should be handed in for recycling. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels. Dispose dried/hardened product residues as construction site/demolition/municipal or domestic waste.
EU limit value for the VOC content
of this product (category A/a): max. 30 g/l (2010). This product contains < 1 g/l VOC.Product Code Paints and Enamels
M-DF01 (Germany)Substances of Content - Declaration
Polyvinyl acetate resin dispersion/emulsion, titanium dioxide, calcium carbonate, silicates, water, additives, preservative (Methylisothiazolinone, Benzisothiazolinone).Customer Service Centre
Tel.: +49 6154 71-71710Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de
International Distribution: Please see www.caparol.com
