Field of Application
Ready-to-use, textured render based on silicone emulsion and nano-quartz-grid structure technology (NQG), suitable for
- Capatect ETICS and Capatect ETICS Natur+
- Uncoated concrete
- Layers of mortar groups PII + PIII as per DIN 18 550-1 and DIN EN 998-1
- Sound coatings of matt emulsion paint or silicates
- Sound mineral based surfaces
- Not for timber and plastic substrates or substrates with efflorescence.
- Reaction to fire: A2-s1,d0 as per DIN EN 13501-1
- Balanced filler-aggregate combination with non-fading pigments
- Highly water vapour permeable
- Ecologically compatible, low odour
- Elegant application
- Higher protection against coating deterioration due to algae and fungus
Packaging/Package Size25 kg bucket
Can be tinted by manufacturer according to colour guides CaparolColor or Caparol 3D-System. In-can-tinting via ColorExpress system. Further shades with luminosity > 20 on request. Shades with luminosity down to 15 possible by using e.g. reinforcing material CarboNit or CarbonSpachtel and/ or a double layer of Muresko CoolProtect paint.
Luminosity < 15 is unsuitable for use within ETICS.
Small quantities can be tinted with CaparolColor or AmphibolinColor colourants (max. 2 % to avoid low consistency).
StorageCool, dry, frost-free and protected from direct sunlight.
Adesive tensile strength
≥ 0.3 MPa as per DIN EN 15824
Fire behaviourA2-s1, d0 as per DIN EN 13501-1
Water permeability (w-value)≤ 0.10 kg/(m2·h0,5), Class W3 (low) as per DIN EN 1062-3
Water vapour permeability (sd-value)< 0.14 m, Class V1 (high) as per DIN EN ISO 7783-2
Variations: Capatect AmphiSilan-Fassadenputz NQG
|Name affix||Texture||Grain Size|
[ mm ]
[ kg/m2 ] ✱
|K10||smoothed scraped plaster||1.0||1.4|
The exact rate of consumption is best established by trials.
✱) without spilling or loss on site; the substrate may affect consumption.
Suitable SubstratesSee Field of application.
Note: Not suitable for horizontal surfaces expecting water loads.
Substrate PreparationThe substrate must be even, clean, dry, solid, sound/stable and free from all substances that may prevent good adhesion. In Germany follow VOB, part C, DIN 18 363, section 3. Remove unsound coatings of enamel, emulsion paint, synthetic (organic) render/plaster and unsound mineral paint coatings completely. Clean adherent paint coatings dry or wet.
Clean surfaces infested with organic growth (fungi/mildew/mould, moss, algae attack) with a high-pressure water jet, in compliance with the regulations. Then use Capatox and allow to dry thoroughly. Clean surfaces contaminated with industrial pollution (factory fumes) or soot by high-pressure cleaner and suitable cleaning agent, in compliance with the regulations.
Method of Application
Apply all textured render with a stainless steel trowel or suitable spraying equipment homogeneously to surface sections. Rub off immediately to the grain size and take off excessive slurry. Treat the K-type render evenly with a plastic trowel or PU-board by circularly "ironing". Groove the R-type render horizontally, vertically or circularly with a plastic trowel as desired.
The surface roughness is influenced by the chosen tool, hence always the same type of texturing tool should be used. For spray application the nozzle size depends on particle sizes.
Working pressure: 0.3 to 0.4 MPa (3 to 4 bar).
Apply thoroughly an homogeneous layer during spray application. Avoid visible overlapping that may be caused by storeys of scaffolding. Always the same craftsmen should finish seamless surfaces to achieve an even texture. To avoid lapping on large-area surfaces, care should be taken to have a sufficient number of craftsmen on the job and to apply the material wet-on-wet without interruption.
Granules and filler are natural products and therefore may occasionally cause slight colour variation in the finished coating. Only use products of the same batch or, if materials from different batches must be applied, mix the entire quantity needed in advance.
Surface Coating System
Primer Putzgrund 610 has to be tinted in matching colour shade before applying tinted render/plaster. Allow thorough drying of priming/intermediate coats before further application.
Capatect ETICS and Capatect ETICS Natur+:
- New reinforcement layers based on mineral mortars: Prime with Putzgrund 610.
- New cement-free reinforcement layers in white: No priming required.
- All tinted renders: Prime reinforcement with tinted Putzgrund 610
- Weathered reinforcement layers (e.g. after winter break): Prime with Putzgrund 610.
- All other substrates: See Technical Information "Untergründe und deren Vorbehandlung" / "Substrates and their Pretreatment".
Processing temperature: + 5 °C to approx. 30 °C. for material, substrate and ambient air during application and curing.
Do not apply in direct sunlight, during strong wind, fog, high relative humidity, and imminent rain or frost.
At 20 °C and 65 % RH: surface-dry after approx. 24 hours.
Cured, recoatable and ready for stress after 2 to 3 days.
The render cures physically by evaporation of water. Drying time is extended by low temperature and high RH. Cover the scaffoldings with tarpaulins to protect the surface from rain during the drying phase (if necessary).
Tool CleaningImmediately after use with water.
Stir Capatect AmphiSilan-Fassadenputz NQG thoroughly with a low-speed stainless steel agitator. If necessary adjust to working consistency with tap water (max. 1 % if manually applied and max. 2 % for spray application).
Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)
Keep out of the reach of children.
Safety data sheet available on request.
Contains: 1,2-Benzisothiazol-3 (2H) -one, 2-methyl-2H-isothiazol-3-one. Can cause allergic reactions.
German hotline for allergy prevention and counsulting service: 0800/1895000 (free of charge from German landlines).
This product is a "treated article" according to EU Regulation 528/2012 (not a biocidal product) and contains the following biocidal active substances: Carbendazim (CAS No 10605-21-7), Isoproturon (CAS No 34123-59- 6) Terbutryn (CAS No. 886-50-0) Octylisothiazolinone (CAS No. 26530-20-1).
DisposalMaterials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. In Germany: Only completely emptied containers should be given for recycling. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels. Dispose dried/hardened product residues as construction site/demolition/municipal or domestic waste.
European Waste Code (EWC) 08 01 12
Risk and Transportation Markings
See Material Safety Data Sheet (MSDS).
See also: Technical Information Nr. 659 Putzgrund 610
Product Code Paints and EnamelsM-SF01 F (outdated)
Other NotesCapatect AmphiSilan-Fassadenputz NQG contains certain active ingredients against fungal and algae growth on it. This depot offers a long-term but nevertheless time-limited protection. Lasting of this depends on project conditions such as the strength of the infestation and the moisture load. It is not a warrenty for permanent protection against fungus and algae growth. That would not be realisable.
Approvals and assessments:
German approvals: Z-33.41-130 Z-33.42-131 Z-33.43-132 Z-33.47-859
European assessments and approvals: ETA-07/0184 ETA-10/0160
CE labelling as per EN 15824: See bucket or www.caparol.de
Customer Service CentreTel.: +49 6154 71-71710
Fax: +49 6154 71-71711
International Distribution: Please see www.caparol.com
Sustainability data sheet
Material safety data sheet
- System instructions AmphiSilan-Fassadenputz NQG R20 SOTON
- System instructions AmphiSilan-Fassadenputz NQG R30 SOTON
- System instructions AmphiSilan-Fassadenputz NQG R20
- System instructions AmphiSilan-Fassadenputz NQG K15
- System instructions AmphiSilan-Fassadenputz NQG K15 SOTON
- System instructions AmphiSilan-Fassadenputz NQG R30
- System instructions AmphiSilan-Fassadenputz NQG K20
- System instructions AmphiSilan-Fassadenputz NQG K20 SOTON
- System instructions AmphiSilan-Fassadenputz NQG K30
- System instructions AmphiSilan-Fassadenputz NQG K30 SOTON