Capadur Wetterschutzfarbe Matt
The matt wood paint with NQG technology
Field of Application
For coloured design and protection of wooden components with limited dimensional stability (such as wooden cladding, shutters, gates, half-timbering, etc.) and wooden components without dimensional stability (such as boarding, fences, shingles, balcony parapets, pergolas, etc.) as well as for downpipes and gutters made of rigid PVC and zinc sheeting. Can be used outdoors.Before coating panel-shaped wood materials such as e.g. solid wood panels or veneer plywood, please observe the instructions in BFS Leaflet No. 18 Para. 2.2.3 ff. In this case, please contact our advisory service.
Mineralised polymer surface through nano quartz lattice technology for long-lasting clean surfaces without loss of elasticity of the coating film.
With film preservation to protect the coating surface against fungal and algae attack.
In most cases, the film preservative provides years of effective protection against mould and algae infestation of the coating surface. However, the use of film preservatives is limited to an ecologically acceptable level. Depending on the biological load, early infestation may therefore occur in individual cases, despite film preservation. On wood-based panels (e.g. plywood, construction veneer plywood, laminated veneer lumber
etc.), infestation must be expected even before the expiry of the usual warranty periods. Depending on the construction and design, roof soffits are also very susceptible to fungal infestation due to increased condensate load, so that freedom from infestation cannot be guaranteed here either. Apart from constructive, i.e. structural measures, the use of film protection agents is the only possible protection against fungal and algal infestation of the coating surface.
Material Properties
- Matt surface finish
- High weather resistance
- Reduced soiling tendency
- Very good colour stability
- Elastic
- Easy, smooth application
- Drip-resistant
- Water vapour diffusible
- Surface temporarily protected against fungal and algal attack
Material Base / Vehicle
NQG-modified plastic dispersion, especially for wooden components.Packaging/Package Size
Standardware:
750 ml, 2,5 Ltr., 10 Ltr.
ColorExpress:
700 ml, 2,4 Ltr., 9,6 Ltr.
Colours
White
Other colours can be tinted via ColorExpress.
When the coating surface is exposed to water, a temporary colour lightening occurs. This appearance is typical for the material and does not affect the functionality of the coating. This also applies to pigment abrasion on the coating surface caused by heavy rubbing.
When using slightly opaque colours (e.g. red, orange, yellow), we recommend a priming coat in the matching priming system colour. Capadur Wetterschutzfarbe Matt is available in priming system colours via ColorExpress.
Colour fastness according to BFS Leaflet No. 26:
Binder: Class A
Pigmentation: Group 1 to 3 depending on colour shade
Gloss Level
Matt
The gloss level may vary depending on the wood surface.
Storage
Please store in a cool place and keep containers tightly closed.
Technical Data
Density: approx. 1.3 g/cm³Suitability according to Technical Information No. 606 Definition of Application Areas
| inside 1 | inside 2 | inside 3 | outside 1 | outside 2 |
| – | – | – | + | + |
| (–) not suitable / (○) limited suitable/ (+) suitable | ||||
Suitable Substrates
Suitable for limited dimensionally stable and non-dimensionally stable wooden components.The substrate must be clean, sound, dry and free from all substances that may prevent good adhesion.
The wood moisture content must not exceed 15 % for limited and non-dimensionally stable wooden components.
The principles of constructive wood preservation must be observed. These are prerequisites for durable wood protection with coating materials (see also BFS Leaflet No. 18).
Substrate Preparation
New wood components:Sand wood surfaces in the direction of the grain, clean thoroughly and remove exuding wood substances such as
z. Remove e.g. resins and resin galls. Break sharp edges.
Old untreated wood:
Sand greyed, weathered wood surfaces down to the sound, load-bearing wood and clean thoroughly. Break sharp edges.
Coated wood:
Completely remove non-stable old coatings down to the sound wood. Sand and clean firmly adhering old coatings.
Zinc, hard PVC:
Ammoniacal wetting agent wash with sanding pad according to BFS No. 5 and 22 or sanding cleaning with sanding pad and Multistar diluted 1 : 5 with water.
Method of Application
New wood components:
Capadur Wetterschutzfarbe Matt is ready-to-use. Apply with brush and roller. Stir before use. Capadur Wetterschutzfarbe Matt is equipped with a film protection agent against fungal and algal attack. Therefore, spraying is only allowed in closed facilities in compliance with environmental and industrial safety regulations.
Instructions for spray application in closed systems:
| Nozzle | Spray angle | Pressure | Dilution | |
| Airless | 0,012 - 0,014 inch | 40 - 60° | 180 - 220 bar | - |
Surface Coating System
| Substrate | Area | Substrate preparation | Impregnation1) | Primer | Intermediate coating | Top coating |
| Wooden components | outside | BFS Nr. 18 | Capacryl Holz SchutzGrund or Capalac Holz-Imprägniergrund | for light shades2) Capalac GrundierWeiß or Capacryl Holz-IsoGrund | Capadur Wetterschutzfarbe Matt | Capadur Wetterschutzfarbe Matt |
| Zinc | outside | BFS Nr. 5 | – | Capacryl Haftprimer | if necessary Capadur Wetterschutzfarbe Matt | |
| Rigid-PVC | outside | BFS Nr. 22 | – | Capacryl Haftprimer | if necessary Capadur Wetterschutzfarbe Matt | |
| solid old coatings | outside | grind/ clean | – 3) | Capacryl Haftprimer 3) | if necessary Capadur Wetterschutzfarbe Matt |
1) According to BFS Leaflet No. 18 and VOB DIN 18363 Part C, an anti-blue stain impregnation is required on wood components at risk of blue stain.
2) Always use Capalac GrundierWeiß or Capacryl Holz-IsoGrund on wood with water-soluble, discolouring ingredients. Treat knots 2 x.
3) Prepare and prime damaged areas in old coatings according to the respective substrate.
Consumption
Approx. 150 ml/m2
The consumption values are reference values that may vary depending on the substrate and substrate condition. Exact consumption values can only be determined by prior test coatings.
Application Conditions
Material, circulating air and substrate temperature: min. 8 °C (favourable range: 10 to 25 °C).Relative humidity: ≤ 70 %
Drying/Drying Time
| At 20°C and 65% relative humidity. | dust-dry | paintable | rainproof |
| After hours | 1 | 12 | 24 |
At lower temperatures, higher humidity and large layer thicknesses, the drying times are delayed.
Tool Cleaning
Clean tool with water after use.
Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)
If medical advice is needed, have packaging or label at hand. Keep out of the reach of children. Contains 1,2-benzisothiazol-3(2H)-one, octhilinone (ISO), 4,5-dichloro-2-octyl-2H-isothiazol-3-one, reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1), 2-methyl-1,2-benzothiazol-3(2H)-one. May cause allergic reactions. Caution. Spraying may produce hazardous respirable droplets. Do not inhale aerosol or mist. According to European Regulation 528/2012 this product is defined as a "treated article” (not a biocidal product) and contains the following biocidal substances: octhilinone (ISO) (CAS-No. 26530-20-1), 4,5-dichloro-2-octyl-2H-isothiazol-3-one (CAS-No. 64359-81-5). Hotline for allergy enquiries: 0800/1895000 (free of charge from the German landline network).
Disposal
Only recycle empty containers. Dispose of liquid material residues at the collection point for old paints/lacquers, dispose of dried material residues as construction and demolition waste or as municipal or household waste.
EU limit value for the VOC content
of this product (cat. A/d): 130 g/l (2010). This product contains max. 130 g/l VOC.Giscode
BSW50Substances of Content - Declaration
Polyacrylic resin, silicates, titanium dioxide, water, glycol ethers, glycols, solvent / coalescent, additives, Preservative, film preservatives.
Further Details
see safety data sheetCustomer Service Centre
Tel.: +49 6154 71-71710Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de
International Distribution: Please see www.caparol.com