Field of Application
Ready-to-use, texturable silicone resin plaster for mineral and organic exterior wall and ceiling surfaces without biocidal film protection. Can be used in conjunction with Capatect façade systems.
Material Properties
- Without biocidal film protection
- Highly permeable to water vapor
- Water repellent
- Smooth processing
- Can be diluted with water
- Graduated, lightfast pigment-filler-granulate combination
Packaging/Package Size
Bucket 25 kgColours
White and tinted
Factory tinting is possible. Suitable for machine tinting with ColorExpress dosing systems.
Further special shades with a light reflectance value > 20 available on request.
Tinting of small quantities is possible by adding CaparolColor (formerly Alpinacolor) or Amphibolin (formerly Amphibolin) (full-tone and tinting colours). Do not add more than 2% of colour, as otherwise the consistency becomes too thin.
The material must be checked for colour accuracy before processing.
Complaints about colour shades cannot be accepted after application.
Use material from the same batch number for coloured materials or contiguous surfaces.
Storage
Cool, protected from frost and avoid large temperature fluctuations. Protect from direct sunlight. Keep opened containers well closed.
Process material within 12 months.
Technical Data
Exterior rendering according to DIN EN 15824Density
ρ ≈ 1.8 g/cm³Water vapour permeability
Category V1 (high) according to DIN EN 15824
sd < 0.14 m according to DIN EN ISO 77833
Adesive tensile strength
Adhesive strength
fH ≥ 0.3 MPa according to DIN EN 15824
Fire behaviour
Class A2-s1, d0 as per DIN EN 13501-1 (non-combustible)Coefficient of water absorption
Category W3 (low) according to DIN EN 15824
w ≤ 0.1 kg/(m2h1/2) according to DIN EN 1062-3
Consistency
PastyVehicle / Binding agent
Silicone resin emulsion, acrylic resin dispersionProduct No.
Product-No. | Product | Structure | Grain size (mm) | Approx. consumption (kg/m2) |
626 FREE | Capatect AmphiSilan Fassadenputz | K20, scraped structure | 2.0 | 2.7 |
626 FREE | Capatect AmphiSilan Fassadenputz | K30, scraped structure | 3.0 | 3.6 |
The consumption figures are guide values without loss of bulk or shrinkage. Building-dependent or processing-related deviations must be taken into account.
Note
Specified fixed values represent average values that may vary slightly from delivery to delivery due to the use of natural raw materials.The "allgemeine bauaufsichtliche Zulassung" (general building authority approval) / "allgemeine Bauartengenehmigung" (general type approval) of the ETICS, VHF or the products and the Technical Informations of the products must be observed.
Suitable Substrates
- Mineral and organically bound renders and paints
- Mineral and organically bound substrates in ETICS
Substrate Preparation
Mask window sills and add-on parts. Carefully cover glass, ceramics, clinker, natural stone, painted, glazed and anodised surfaces as well as surfaces to be protected.
The substrate must be stable, even, clean, dry, frost-free and free of adhesion-reducing residues. If necessary, the load-bearing capacity can be ensured by using suitable primers.
Substrates, especially undercoat renders, must be evenly dried to avoid colour deviations in the finishing render.
Before applying the decorative render, we recommend priming with Putzgrund 610, coloured if necessary, to improve the application and accelerate the film formation of the finishing render, especially on fresh mineral base coats.
Preparation of Material
Ready to use.
Adjustable to working consistency with max. 2 % water.
Stir the contents of the container thoroughly with a slow-speed agitator.
Method of Application
Apply the render over the entire surface using a stainless steel trowel and smooth it down to the grain. Immediately afterwards, use a plastic trowel or a plastic float to spread it evenly in a circular motion.
The choice of tool influences the roughness profile of the surface, so always work with the same textured discs.
Finish contiguous surfaces without interruption to avoid build-up in the textured layer. Divide large façades into sections, wet-on-wet apply and texture continuously.
Due to the use of natural fillers and granules, slight colour variations are possible. Therefore, only use material with the same batch number on contiguous surfaces, or mix material from different batches beforehand.
Surface Coating System
The risk of attack by micro-organisms can be significantly reduced by using a facade paint that has been treated with a film protection agent.
If the light reflectance value is below 20, after the render has dried, coat the render in the ETICS with a solar-reflecting facade paint (CoolProtect, TSR value ≥ 25) in at least two layers, depending on requirements. On solid wall structures, special measures are to be taken for LRV < 30, e.g. an additional reinforced base coat with full-surface fabric inlay on the lightweight base coat; for LRV < 20, additionally a solar-reflecting facade paint with TSR ≥ 25.
Note the limits of feasibility in the respective system.
Application Conditions
During the application and in the drying phase, the ambient and substrate temperatures must not be below +5 °C and above +30 °C.
Do not apply in direct sunlight, strong wind, fog or high humidity. In this context, we refer to the leaflet "Verputzen, Wärmedämmen, Spachteln, Beschichten bei hohen und tiefen Temperaturen" (Rendering, Thermal Insulation, Filling, Coating at High and Low Temperatures) from the Bundesverband Ausbau und Fassade (Federal Association for Finishing and Facades).
In unfavourable weather conditions, suitable measures must be taken to protect the treated façade surfaces.
Drying/Drying Time
Primer and intermediate coats must be dry before further application.
The waiting time for recoating depends, among other things, on the weather conditions and the layer thickness. The specifications refer to ambient temperatures of 20 °C and 60 % relative humidity and serve as a guide.
The drying or curing of the material takes place through chemical-physical processes and the release of the water it contains, i.e. its evaporation. Cool and humid environments delay these processes.
- Surface dry after approx. 24 h
- Completely dry, loadable and paintable after approx. 48 hours
Tool Cleaning
Rinse with water immediately after use in accordance with legal regulations.Example for Machine Equipment
- Feed pump e.g. m-tec P 25 V
Delivery hoses:
Start hoses, inner Ø 35 mm; end hose, inner Ø 25 mmConveying distances:
Maximum delivery distance approx. 50 m; delivery head 30 m
(depending on temperature and device)Sprayer:
Nozzle Ø dependent on the grain sizePre-flush delivery hoses with lime slurry or paste before regular operation.
If work is interrupted, do not leave the delivery hose in direct sunlight, cover the material container with foil, for example, and keep the gun and nozzle under water. Stand for max. 30 min. until further processing, otherwise the material in the hose may harden.
Before a work break, the material container in the feed pump of the ‘open system’ (continuous mixer + feed pump) must be emptied as far as possible to prevent material tunnelling when restarting. If this is not observed, the material may have to be made ‘passable’ before the machine is started up (with the machine switched off). Further information on this can be found in the Caparol "Handbuch der Spritztechnologie" (Spray Technology Manual).The specifications of the machine manufacturer must be observed.
Note
This product is equipped with special active substances against fungal and algae growth. The depot of active substances offers long-lasting, temporary protection, the duration of which depends on the object conditions, e.g. the moisture load, the location, the architectural design, etc.. It is therefore not possible to permanently prevent fungal and algae growth. The risk of infestation by microorganisms can be significantly reduced by applying a facade paint with film protection.Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)
May cause an allergic skin reaction. Avoid breathing mist or vapors. Contaminated work clothing should not be allowed out of the workplace. Wear protective gloves. If skin irritation or rash occurs: Get medical advice/ attention. Take off contaminated clothing and wash it before reuse.
Dispose of contents/ container to an approved waste disposal plant.
Contains: 1,2-benzisothiazol-3(2H)-one, 2- methylisothiazol-3(2H)-one, reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1).
Warning! Hazardous respirable droplets may be formed when sprayed. Do not breathe spray or mist.
For commercial/industrial applications. Wear long trousers! Avoid prolonged skin contact with the plaster. Thoroughly clean any affected areas of the skin immediately using water. The longer fresh plaster remains on the skin, the greater the danger of serious skin damage. Keep children away from fresh plaster!
The safety instructions issued by the manufacturer must be strictly followed during the application phase. Further technical information is available by calling +49 (0) 6154/7171710 and advice for allergy sufferers can be obtained by calling +49 (0) 800/1895000.
GISCODE: BSW20.
VOC content in accordance with Directive 2004/42/EC: This product contains max. 10 g/l VOC.
Declaration of ingredients according to VdL directive 01 (Germany): polyacrylic resin, silicone resin, calcium carbonate, silicates, mineral pigments / fillers, aluminum hydroxide, titanium dioxide, water, aliphatics, additives, Preservative.
Customer Service Centre
Tel.: +49 6154 71-71710Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de
International Distribution: Please see www.caparol.com