Capacryl PU-Matt NAST

Suitable Substrates

Primed wood component parts, primed metals and unplasticized/rigid PVC, indoors.
The substrate must be clean, sound/stable, dry and free from all substances that may prevent good adhesion.

Substrate Preparation

Wooden Parts:
Sand the surface in fibre direction, clean thoroughly and prime with Capacryl Holz-IsoGrund, if necessary. 

Iron, Steel:
Derust according to industry standard SA 2½ (blasting) or ST3 (mechanically) according to DIN EN ISO 12 944-4, followed by an anti-rust priming coat.

Zinc (Galvanised Substrates), Unplasticized/Rigid PVC:
Wash with light ammonia solution or Gescha Multistar using a sanding pad/non-woven web as per German BFS-Merkblätter (Data/Fact Sheets) Nos. 5 and 22. Allow to dry and prime with Capacryl Haftprimer.

Aluminium, Copper:
Clean with nitro-thinner (diluent for cell lacquers) or Multistar using a sanding pad/non-woven web as per German BFS-Merkblatt (Data/Fact Sheet) No. 6 (aluminium). Allow to dry and prime with Capacryl Haftprimer.

Existing Paint Coatings:
Sand the surface and/or treat with alkaline solution. Remove unstable existing coatings and prime as per substrate requirements.

Method of Application

Guidelines for Spray Application:

	Nozzle/Frontend	Adjustment Quantity of Material	Adjustment Quantity of Air	Dilution
Wagner XVLP FinishControl 3500/5000/5500	Caparol NAST	8 - 10	2/3 or 7 - 8	undiluted
Titan Focus 700	Caparol NAST	8 - 10	2/3 or 7 - 8	undiluted
Graco Capacryl NAST HVLP Spray	Edge 2 NAST	6 - 7	max.	undiluted

Application:
Capacryl PU-Matt NAST is particularly adjusted for use with the above mentioned spray equipment and Caparol NAST-Frontend/Capacryl NAST HVLP Spray. Only this combination of material and equipment enables a nearly mist-free spray application.

Spray Technique:
Adjustment for coating surfaces: "Flachstrahl" (flat jet). Spray slowly lengthwise with an overlap of min. 50 % and in a spray distance of 15 cm, applying wet-on-wet.
Do not apply cross-coats!
Allow to dry and apply a second coat in the same manner, if necessary.

Surface Coating System

Substrate	Use 1)	Substrate Preparation	Priming Coat	Intermediate Coat 3)	Finishing Coat 4)
Wood, derived timber products	interior	sanding/cleaning	Capacryl Holz-IsoGrund 2)	if necessary: Capacryl PU-Vorlack	1 - 2 x Capacryl PU-Matt NAST
Iron, steel	interior	derust/cleaning	Capalac AllGrund
Zinc (Galvanised surfaces)	interior	BFS No. 5	Capacryl Haftprimer
Aluminium/copper	interior	BFS No. 6	Capacryl Haftprimer
Rigid PVC	interior	BFS No. 22	Capacryl Haftprimer
Stable existing paint coatings	interior	slightly sanding	Capacryl Haftprimer

1) Definition of suitable application areas: see Technical Information No. 606. 2) Always apply Capacryl Holz-IsoGrund on wood with content of water-soluble, discolouring substances (2x on knots). 3) The intermediate coat should match the finishing coat in shade. For colour shades of low opacity (e.g. red, yellow and orange pigmented) a matching colour is automatically selected via ColorExpress, thus a better opacity is achievable for finishing/top coats. This shade may differ from the selected colour in favour of the hiding power of top coats. 4) Colour shades of low opacity (e.g. yellow/red/orange pigmented) may require an additional coat. Note: Adhesion must always be tested in advance for powder coatings, coil coatings and other critical substrates by trials (coating a test area on site).

Consumption

Approx. 120 - 160 ml/m² per coat.
Consumption is a guide value and may vary, depending on substrate requirements. Determine the exact amount of material required by coating a test area on site.

Application Conditions

Low Temperature Limit for Application and Drying:
Min. 8 °C for product, substrate and ambient air.

Drying/Drying Time

At 20 °C and 65 % relative humidity.	dust dry	recoatable	cured
after hours	1 - 2 hours	8 - 10 hours	48 hours

Lower temperatures and higher humidity extend the drying time.

Tool Cleaning

Immediately after use with water.

Please Note (Status as at Date of Publication)

If medical advice is needed, have product container or label at hand. Keep out of reach of children. Contains 1,2-benzisothiazol-3(2H)-one, reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1). May produce an allergic reaction. Warning! Hazardous respirable droplets may be formed when sprayed. Do not breathe spray or mist. Keep out of reach of children. For spraying work, use combination filter A2/P2 and protective goggles. Use dust filter P2 for grinding work. Ensure thorough ventilation during application and drying. Avoid eating, drinking and smoking while using the paint. In case of contact with eyes or skin, rinse immediately with plenty of water. Do not allow to enter drains, waterways or soil. Clean tools immediately after use with soap and water.

Germany: Advice for allergy sufferers with isothiazolinone allergy: Hotline 0180/5308928
(0.14 €/minute from German landline, MTS max. 0.42 €/minute).

Disposal

Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures.
Germany: Only completely empty containers should be handed in for recycling. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels. Dispose dried/hardened product residues as construction site/demolition/municipal or domestic waste.

EU limit value for the VOC content

of this product (category A/d): max. 130 g/l (2010). This product contains max. 130 g/l VOC.

Giscode

BSW30

Substances of Content - Declaration

Polyurethane/acrylate resin, titanium dioxide, coloured pigments, mineral fillers, water, glycols, glycol ether, additives, preservatives (methyl-/benzisothiazolinone).

Customer Service Centre

Tel.: +49 6154 71-71710
Fax: +49 6154 71-71711
e-mail: kundenservicecenter@caparol.de

International Distribution: Please see www.caparol.com