Field of ApplicationHigh-quality coloured paint/top-coat lacquer for finishing gloss coats on dimensionally stable wooden component parts, metals and unplasticized (rigid) PVC, in exteriors and interiors. Also suitable for use on hot water radiators with the exception of white colour shades.
Due to a material typical odour of alkyd enamels (alkyd resin varnishes), it is advisable to use Capacryl PU-Gloss for top coats on large, seamless interior surfaces instead.
- Non-aromatic solvent (free of aromatic hydrocarbons).
- Excellent colour stability and gloss retention.
- High gloss finished.
- Long open time.
- High stability (low sagging).
- Excellent opacity, high covering power on edges.
- High impact strength and shock resistance.
- Elegant and easy application.
- Superior flow.
- Resistant to common household cleaning agents (detergents) and short-term resistance against weak acids and alkalis.
Material Base / VehicleSilicone alkyd resin, solvent-based, free of aromatic hydrocarbons.
Packaging/Package SizeStandard Colours:
125 ml, 375 ml, 750 ml, 2.5 litres
✱not all standard colours are available in all package sizes.
375 ml, 750 ml, 2.5 litres, 10 litres
White (Weiß), RAL 3000, RAL 5010, RAL 6011, RAL 7001, RAL 7035, RAL 8017, RAL 9001, RAL 9002, RAL 9005 and effect colours RAL 9006 White Aluminium (Weißaluminium) and RAL 9007 Grey Aluminium (Graualuminium)
More colour shades can be tinted via ColorExpress (Capalac mix).
When applying colours with low opacity, like Red, Orange or Yellow, it is advisable to apply one priming coat using the matching colour shade of our Priming System. Priming System colours are available via the ColorExpress tinting technique for the following products: Capalac Hochglanz-Buntlack, Capalac AllGrund and Capalac Vorlack.
Note: A material typical yellowing effect may occur on the surface of white and light-coloured alkyd enamels (caused by low UV radiation, heat or chemical influences due to e.g. ammonia vapour from detergents, adhesives, paint or sealing compounds). This yellowing is no product defect and cannot be objected.
Colour Resistance according to BFS Data Sheet No. 26:
Binder: Class B
Pigmentation: Group 1 to 3, depending on the colour.
StorageKeep in a cool place.
Keep cans/containers always tightly closed.
DensityApprox. 1.0 g/cm³, depending on the colour
Suitability according to Technical Information No. 606 Definition of Application Areas
|Interior 1||Interior 2||Interior 3||Exterior 1||Exterior 2|
|(–) inapplicable / (○) of limited suitability / (+) suitable|
Suitable SubstratesPrimed and pre-coated wood, metal and unplasticized (rigid) PVC.
Do not apply on andonized aluminium.
The substrate must be clean, sound/stable, dry, and free from all substances that may prevent good adhesion.
Max. permissible moisture content in dimensionally stable wood: 13 %.
Roughening and cleaning the primered surface.
Method of ApplicationGuidelines for Spray Application:
|Ø Nozzle||Pressure||Thinning/Dilution||Heating of Material|
|Aircoat TempSpray✱||0,009 - 0,013 inch||150 bar||-||35 °C|
(only suitable for RAL 9006 and 9007)
|1.6 mm||2.5 bar||+ 10% Capalac PU hardener and up to 25-30 % AF-thinner, if necessary; viscosity DIN 4 mm: approx. 45 seconds||20 °C|
Capalac Hochglanz-Buntlack is applied by enamel paint brush, roller or spraying equipment. Stir well before use.
Aircoat spray application of material in delivered consistency is possible by heating (TempSpray).
Application of RAL 9006 and 9007:
An even surface can only be achieved with high-pressure spraying equipment, but sometimes a slight clouding/blushing effect may be noticeable, when the material is applied on large, seamless surfaces.
Colour differences may occur, when different application methods are used.
10 % of PU hardener must be added to the material, when standard colours RAL 9006 and RAL 9007 are to be applied, because these two colour variations of the product are special 2-component enamels/varnishes.
Follow the safety advice in Technical Information No. 093 (Capalac PU Hardener).
Surface Coating System
|Substrate||Use||Substrate Preparation||Impregnation||Priming Coat||Intermediate Coat||Finishing/Top Coat|
|Wood, derived materials||interior||sanding/cleaning||–||Capalac Vorlack||if necessary Capalac Hochglanz-Buntlack||Capalac|
|Wooden parts||exterior||BFS Data Sheet No. 18||Capalac Holz-Imprägnier-grund||Capalac Vorlack||Capalac Hochglanz-Buntlack|
|Iron, steel||interior||derusting/cleaning||–||Capalac AllGrund||if necessary Capalac Hochglanz-Buntlack|
|exterior||derusting/cleaning||–||2x Capalac AllGrund||CapalacHochglanz-Buntlack|
|Zinc (galvanised substrates)||interior||BFS Data Sheet No. 5||–||Disbon 481 EP-Uniprimer or Capalac AllGrund||if necessary Capalac Hochglanz-Buntlack|
BFS Data Sheet No. 5
Disbon 481 EP-Uniprimer or 2 x Capalac AllGrund
|Aluminium||interior||BFS Data Sheet No. 6||–||Capalac AllGrund||if necessary Capalac Hochglanz-Buntlack|
BFS Data Sheet No. 6
|Rigid PVC||interior/exterior||BFS Data Sheet No. 22||–||Capalac AllGrund||if necessary Capalac Hochglanz-Buntlack|
|Stable, existing paint coatings||interior/exterior||roughening /alkali treatment||–1)||Capalac AllGrund 1)||if necessary Capalac Hochglanz-Buntlack|
|Uncoated radiators||interior||derusting/cleaning||–||Capalac AllGrund |
up to 100 °C
|Capalac 2)Hochglanz-Buntlack||2)Capalac |
|Precoated radiators (prefab)||interior||roughening||–||Disbon 481 EP-Uniprimer |
up to 100 °C
|1) Pretreat defects in existing enamel coatings according to substrate requirements.|
2) Do not apply white shades on radiators to avoid yellowing.
Note: Adhesion must previously be tested for powder coatings, coil coatings and other such critical substrates by a trial coating.
|Consumption ml/m2 per Coat✱||70 - 100||80 - 110||120|
Determine the exact amount of material required by coating a test area on site.
Application ConditionsLower Temperature Conditions for Application and Curing:
Min. 5 °C for product, ambient air and substrate.
Relative humidity must not exceed 80 %.
|At 20 °C, 65 % relative humidity||dust dry||touch dry||recoatable (brush)||recoatable (spraying)|
|after hours||4||8 - 10||24||8 - 16|
Lower temperatures and higher humidity or higher quantities of applied material extend the drying time.
The use of Capalac PU Hardener (PU-Härter) is essential for colours RAL 9006 and RAL 9007 to compensate delayed drying of both materials. It is mandatory to follow the Safety Advice given in Technical Information No. 093.
Tool CleaningImmediately after use with white spirit.
Special Risks (Hazard Note) / Safety Advice (Status as at Date of Publication)Flammable liquid and vapour. Harmful to aquatic life with long lasting effects. If medical advice is needed, have product container or label at hand. Keep out of reach of children. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. Avoid release to the environment. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. Repeated exposure may cause skin dryness or cracking. Contains bis(1,2,2,6,6-pentamethyl-4-piperidyl) sebacate, methyl 1,2,2,6,6-pentamethyl-4-piperidyl sebacate. May produce an allergic reaction. Use P2 dust filter for grinding. Do not breathe spray dust. Use A2/P2 combination filter for paint spraying.
DisposalMaterials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities. Particular attention should be made to removing wastage from site in compliance with standard construction site procedures.
In Germany: Only completely empty containers should be handed in for recycling. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels. Dispose dried/hardened product residues as construction site/demolition/municipal or domestic waste.
EU limit value for the VOC content
of this product (category A/d): max. 300 g/l (2010). This product contains max. 300 g/l VOC.
VOC content of standard colours RAL 9006 and RAL 9007 with 10 % content of PU Hardener: Limit value (Category A/j): max. 500 g/l (2010). This product contains max. 500 g/l VOC.
Product Code Paints and EnamelsM-LL01 (Germany)
Substances of Content - DeclarationAlkyd resin, titanium dioxide, colored pigments, aliphatics, additives.
Further DetailsSee Material Safety Data Sheet (MSDS).
Customer Service CentreTel.: +49 6154 71-71710
Fax: +49 6154 71-71711
International Distribution: Please see www.caparol.com
Material safety data sheet
- System instructions Capalac mix Hochglanzlack Basis Transpar
- System instructions Capalac Hochglanz-Buntlack Basis Weiß
- System instructions Capalac Hochglanz-Buntlack RAL 8017
- System instructions Capalac Hochglanz-Buntlack Weiß
- System instructions Capalac Hochglanz-Buntlack RAL 6011
- System instructions Capalac Hochglanz-Buntlack RAL 7001
- System instructions Capalac Hochglanz-Buntlack RAL 5010
- System instructions Capalac Hochglanz-Buntlack RAL 9001
- System instructions Capalac Hochglanz-Buntlack RAL 7035
- System instructions Capalac Hochglanz-Buntlack RAL 3000
- System instructions Capalac Hochglanz-Buntlack RAL 9007
- System instructions Capalac Hochglanz-Buntlack RAL 9005
- System instructions Capalac Hochglanz-Buntlack RAL 9006